Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.
|Published (Last):||1 April 2010|
|PDF File Size:||1.25 Mb|
|ePub File Size:||11.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
A telegram is transmitted within 20 seconds if the power status changes by min. Registration for newsletter Would you like to stay up to date and inform yourself about products, services and offers? Relays with suitable functions to feed tlz12-8e-230b the switching voltage signal of a dimmer switch. A power telegram is transmitted every seconds and the display is updated.
If light switches cannot be replaced by push-button light switches, there is a separatecontrol input for light switches. Typical connection C8 For installation. Only a single MSR12 must provide eltakl outer terminal resistance. The current dimming position as well as the adjustable minimum brightness level determine the dimming time max. It can therefore be reduced until the loads are barely detectable.
To display the correct break-down of prices with or without VATplease select:.
This impulse group switch serves to implement commands generated by the sensor relays or by switches and push-buttons and controls a motor, a motor isolating relay MTR The counter is reset to 0. Off-delay time settable from 1 to 12 min with the top rotary switch.
The set release delay RV delay time starts when the control contact opens and if a set operating delay has elapsed. If this impulse switch with integrated relay function is in a circuit, which is monitored by a FRV mains disconnection relay, no additional base load is required.
The maximum load will be reduced for shorter times as follows: The enclosed window contact consists of a Eltko relay with terminals and a solenoid. Typical connection V UC checkback signal If N is connected, the zero passage switching is active.
Furthermore, here it is decided if the switch position should be kept or not after a power failure: Switch-off early warning and permanent light by push-button can also be elgako on in this position. The upper rotary switch adjusts the dimming speed. Similarily, provision made for local control through A3 and A4 are not shown.
If a new small load is switched on for more than 24 hours, the total current drawn by the monitored circuit is less than mA, and in the meantime the light has been switched on and off, the new load is learned in and the conductor is switched off.
The basis of current A will be set with the lower rotary switch A. An arrow on the right of the abbreviation indicates the blocking status. All other control inputs stay active for local and central control. If the function ER is selected a glow lamp current is not permitted. It blinks while the relay contact is open closedand is continuously ON as long as the relay contact is closed open.
Products and prices 2010
If the permanent light function is switched on, the function can be activated by pressing the push-button for longer than 1 second. The switching mode “one lamp” or “additional lamps” is set with a rotary switch on the front. Technical data page J7. This drastically reduces wear.
TLZ12 8E V UC – Eltako Продажни цени
Press the MODE key again to restart the input cycle. An equivalent capacitance of 10F per lamp may be calculated. Product group G, page G3. To achieve this, simply connect the N conductor to the terminal N and the phase conductors to 1 L3 L or 5 L. Switching operation for children’s rooms KI universal switch or direction switch: Standby loss 0,9 Watt only. G7The Modular ApproachSwitching on the future.
The function ESV, impulse switch with release delay up to minutes, can be selected optionally. With the lower rotary switch 18 different functions may be selected: In case of a power failure the system is disconnected in a defined mode. This prolongs lifetime and reduces or avoids standby loss.
aslme78 | eBay Stores
This is the setting ex works. Supply voltage and switching voltage V. Business customer or Private customer.
If the function STS is set, the lighting is switched on again after a power failure provided the set time has not yet elapsed.